Worldwide Shipping
Worldwide Shipping
Brand Name: HDCSUN
DIY Supplies: ELECTRICAL
Origin: Mainland China
Model Number: K300
Type: Silicone Sealant
is_customized: Yes
Certification: RoHS
50ml Kafuter UV Glue UV Curing Adhesive K-300
Transparent Crystal and Glass Adhesive with UV Flashlight
Buyers please note: This liquid item can not be sent by DHL FEDEX TNT UPS
Product Features:
K-300 is a modified UV or visible light curing acrylic adhesive, low odor, high transparency, high bonding strength,low viscosity, easy deaeration , typically used in large- area glass crystal bonding, such as : glass mosaic,glass crafts, crystal crafts.
Key performance indicators:
Appearance: colorless or light yellow transparent liquid
Viscosity cps: <110 (Brookfield DV-II viscometer , 25 ° C, SC 4-15 rotor 150rpm)
Hardness ( Shore D): 75 (GB / T 531-1999 curing test )
Typical curing nature:
K-300 will be cured under ultraviolet light , the sun will slowly solidified . 220-260nm light source helps surface cure .
Cure rate , depth, and ultimately curing effect is dry and UV light source , exposure time , light transmittance related material . Suggested by experiments to determine the final curing process .
Positioning time:
10 seconds -125w high-pressure fluorescent , 4 mW / cm ⊃2; UVA
Full cure time:
180 seconds -125w high-pressure fluorescent , 4 mW / cm ⊃2; UVA
Typical cured properties:
Tensile shear strength (GB 7124-86) overlapped area of 25 × 12.5 = 312.5mm2: glass / stainless steel , ≥ 10MPa
Use these steps:
1 Depending on the material surface treatment , surface dry and clean , no weak boundary layer ;
2 interface adhesive bonding material on the need for continuous coating, be careful not to disperse ;
3 light positioning the glue into the short ultraviolet curing lamp radiation, until the hand nudging fixed;
4 to remove the excess glue with a knife to scrape the glue overflow , or a soft cloth , paper towel and gently erase the excess glue can also be dipped in acetone, alcohol wipe ;
5 full cure time high radiation , until fully cured , note the temperature is not too high ;
6 dipped in acetone, alcohol, cleaning materials with a soft cloth or paper towel and gently wipe the bonding good material .
Instructions for use:
1 , the adhesive surface clean, dry and free of grease , you can wipe with acetone , hair dryer .
2, the UV lamp positioned curing , the curing rate is dependent on the glue to absorb light energy from the light source associated with , the light transmittance material and other factors .
3 , the operation should not squeeze too hard to be sticky , and shall not be repeatedly moved apart
adherend.
4, using the rest of the glue not fall back to the original packaging to avoid contamination.
Note:
Avoid contact with eyes, skin and clothing . This pair of eyes and a slight skin irritation.
If accidentally splashed into the eyes , rinse immediately with plenty of water , as there does not need to go to hospital.
Rinse immediately with soap and water after skin contact. Please wash before they can wear the clothing.
Do not allow contact with children .
Storage: This product is sensitive to light and heat , you need storage in a cool, dry place, away from light below 28 ° C, valid for one year .
Package includes:
1 x 50ml K-300 Glue
1 x 9LED UV flashlight(not include battery)
Collections: Recommended products (Seguno)
Type: Unknown Type
You can use this popup to promote newsletter signups, but that's not all! You could also omit the form and include action buttons linked to your pages and products instead. Or, use the popup to present an 'agree-to-terms' message that must be accepted before a visitor enters your shop!